Insulation in New Braunfels, TX
Crawl space encapsulation and vapor barrier installation in New Braunfels typically runs $2,800-$6,500 for most homes, with full encapsulations on larger Hill Country properties reaching the upper end. We’re Envelope Insulation Co., and we treat every crawl space job as a moisture-management and air-sealing project before insulation ever enters the picture. Our crews serve New Braunfels from our San Antonio dispatch office, and a live person answers at (737) 227-6219 around the clock.
New Braunfels presents a specific challenge: the 2010s-2020s production homes that dominate this market were built fast to minimum IECC code, with crawl spaces that often lack proper ground cover, sealed perimeter walls, or dehumidification. The combination of Hill Country limestone substrate, seasonal humidity swings, and slab-on-grade construction means moisture migrates upward through crawl space floors year-round, degrading floor insulation and creating conditions for mold and wood rot in homes that are barely a decade old.
Why New Braunfels Homes Are Different
New Braunfels has been one of the fastest-growing cities in the United States for over a decade, and that velocity shows in the housing stock. The master-planned communities along SH-46, FM-306, and the I-35 corridor were built rapidly with production-builder crews working to tight schedules. Attic insulation was typically blown to R-30, often compressed by subsequent trade work or unevenly distributed around duct chases and top plates. In summer, Hill Country attic temperatures exceed 140°F, forcing HVAC systems to run near-continuously and exposing every weakness in the thermal envelope.
The February 2021 Winter Storm Uri revealed another layer: even homes built in the 2010s suffered catastrophic pipe freezes when wall and mechanical-chase insulation proved inadequate against extended sub-freezing temperatures. New Braunfels sits at the IECC climate zone 2/3 boundary, which means insulation upgrades must address both extreme cooling loads and periodic hard-freeze resilience. The historic German-heritage limestone and wood-frame structures downtown and in Gruene present different air-sealing and vapor-management challenges entirely, requiring assessment before any material is specified.
Our Main New Braunfels Services
Most calls from New Braunfels homeowners center on two problems: attics that can’t hold cool air in summer, and crawl spaces that feel damp year-round. Here are the three services we route to dedicated city pages.
Attic Insulation in New Braunfels
In the subdivisions along FM-306 and the SH-46 east corridor, we regularly find R-30 attic insulation that has settled into the low R-20s within five to eight years of construction. Upgrading these barely-decade-old homes to R-49 or R-60, with proper air sealing first, is the core opportunity here. We publish before-and-after blower-door numbers on every job so you can verify the performance change. Attic Insulation in New Braunfels covers full scope, pricing, and what the documentation looks like when we leave.
Spray Foam Insulation in New Braunfels
Spray foam makes sense in New Braunfels for roofline encapsulation in homes with HVAC ducts in the attic, for rim joist sealing in crawl spaces with complex geometry, and for select wall-cavity applications where injection foam isn’t viable. We specify open-cell and closed-cell products from Icynene and Demilec based on the moisture drive and temperature conditions of each assembly. Spray Foam Insulation in New Braunfels details when foam is the right choice and when it isn’t.
Blown-In Insulation in New Braunfels
Blown-in fiberglass and cellulose remain the most cost-effective path to R-49+ in New Braunfels attics, especially when the existing insulation can be supplemented rather than removed. We source from Owens Corning, Johns Manville, and GreenFiber, and we never blow new material over an unsealed attic floor. Blown-In Insulation in New Braunfels explains our process, including the air-sealing prerequisite that defines every Envelope job.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Before
AfterCrawl Space Encapsulation & Vapor Barrier in New Braunfels
Crawl space encapsulation in New Braunfels addresses a problem the production builders largely ignored: bare earth or thin poly ground cover in crawl spaces that allows soil moisture to evaporate upward into the floor assembly year-round. With Hill Country limestone substrate and seasonal humidity that can spike above 70% even in winter, these conditions degrade fiberglass floor insulation, raise indoor humidity, and create the mold and wood-rot conditions we find in homes as new as 2018. Crawl Space Encapsulation & Vapor Barrier is our full hub page on this service.
In the fast-built subdivisions, we’ve found crawl spaces with no perimeter sealing, disconnected downspouts dumping water against foundation walls, and bath fan ducts terminated in the crawl space rather than exterior. Each of these conditions must be corrected before encapsulation begins, or the sealed cavity becomes a moisture trap rather than a controlled environment.
Crawl Space Encapsulation
Signs you need it
Your crawl space has standing water after rain, visible mold on floor joists, or a musty smell that enters the living space through gaps in the floor.
What it costs in New Braunfels
Full crawl space encapsulation in New Braunfels typically runs $4,200-$6,500 for homes under 2,500 square feet, with larger Hill Country properties or complex perimeter walls reaching $8,000-$10,500.
How we do it
We install a 20-mil reinforced vapor barrier across the entire ground surface, sealed at seams and perimeter walls, then add rigid foam insulation on foundation walls and a dehumidifier sized to the sealed volume, with a condensate pump to exterior.
Crawl Space Vapor Barrier
Signs you need it
Your crawl space has bare earth or thin torn poly sheeting, and you want to stop ground moisture evaporation before it reaches floor joists.
What it costs in New Braunfels
Vapor barrier installation alone in New Braunfels typically costs $1,800-$3,200 for standard crawl spaces, with thicker reinforced membranes or complex pier-and-beam foundations adding $400-$800.
How we do it
We remove existing debris and damaged poly, grade the earth surface for drainage, then install and seam-seal a reinforced vapor barrier with mechanical attachment at perimeter walls and piers.
What Crawl Space Encapsulation & Vapor Barrier Costs in New Braunfels
| Item | Typical range in New Braunfels |
|---|---|
| Basic vapor barrier (ground cover only) | $1,800 - $3,200 |
| Full encapsulation with wall insulation | $4,200 - $6,500 |
| Large or complex encapsulation with dehumidifier | $6,500 - $10,500 |
Does encapsulation include mold remediation?
Encapsulation stops future moisture but does not remove existing mold; we treat visible microbial growth with EPA-registered products before sealing, and we document the pre-encapsulation condition with photos you receive.
How long does crawl space encapsulation take?
Most New Braunfels encapsulations take two to three days, with day one for prep and moisture-source correction, day two for barrier and insulation installation, and day three for dehumidifier commissioning and final documentation.
Radiant Barrier Installation in New Braunfels
Radiant barrier installation in New Braunfels is a direct response to a measurable condition: attic temperatures that exceed 140°F for months each summer, radiating heat downward through ductwork and ceiling assemblies. In the production homes built along SH-46 and FM-306, HVAC ducts are typically routed through unconditioned attics, and the combination of low R-value insulation and high radiant heat gain forces compressors to run near-continuously in July and August. A properly installed radiant barrier can reduce attic surface temperatures by 20-35°F, lowering the radiant heat load on ducts and ceiling drywall. Radiant Barrier Installation covers our full approach.
We install radiant barriers only after attic air sealing is complete, because a leaky attic floor allows conditioned air to escape regardless of how much radiant heat is reflected.
Attic Radiant Barrier
Signs you need it
Your upstairs rooms stay hot after sunset, your HVAC runs constantly in summer, or your ducts are in the attic and the metal feels hot to touch.
What it costs in New Braunfels
Attic radiant barrier installation in New Braunfels typically costs $1,400-$2,800 for homes under 2,500 square feet, with larger attics or steep pitches reaching $3,200-$4,500.
How we do it
We staple perforated radiant barrier foil across attic rafters or truss chords, maintaining a minimum 3/4-inch air gap above the foil, with strategic cuts around vents and electrical to preserve attic ventilation paths.
Radiant Barrier Roof Deck
Signs you need it
You’re replacing your roof and want radiant barrier integrated at the roof deck rather than retrofitting foil in a finished attic.
What it costs in New Braunfels
Roof-deck radiant barrier during reroofing in New Braunfels adds $1.80-$3.20 per square foot of roof area, or $2,800-$5,500 for typical production-home roof sizes.
How we do it
We install radiant barrier sheathing or foil-faced decking during roof replacement, with taped seams at panel edges, integrated with the roofing contractor’s schedule so the barrier is protected from weather.
What Radiant Barrier Installation Costs in New Braunfels
| Item | Typical range in New Braunfels |
|---|---|
| Attic radiant barrier (foil on rafters) | $1,400 - $2,800 |
| Large or steep attic radiant barrier | $3,200 - $4,500 |
| Roof-deck radiant barrier (with reroof) | $2,800 - $5,500 |
Does radiant barrier work with existing insulation?
Yes, radiant barrier complements existing insulation by reducing radiant heat gain, but it does not replace the need for adequate R-value; we assess your current insulation depth before recommending barrier placement.
Will radiant barrier make my attic colder in winter?
Perforated radiant barriers have minimal winter penalty in New Braunfels because the dominant load is cooling, and the same foil that blocks inward summer radiation has limited effect on the much smaller winter heat loss through the ceiling.
Insulation Removal & Replacement in New Braunfels
Insulation removal and replacement in New Braunfels is increasingly common in homes that are only five to fifteen years old, because the production-built stock along I-35 and the FM-306 corridor was insulated fast and often disturbed by subsequent electrical, plumbing, and HVAC trade work. We find compressed, displaced, or moisture-damaged fiberglass in attics that should still be performing at full R-value, and we find floor insulation in crawl spaces that has fallen or degraded from ground moisture contact. Insulation Removal & Replacement details our containment and disposal process.
Every removal job begins with a written scope that specifies what comes out, what condition we expect to find, and what replaces it, with photos of the pre-work condition delivered before any material is ordered.
Contaminated Insulation Removal
Signs you need it
Your attic insulation has visible mold, rodent droppings, or urine staining, or you smell musty or ammonia odors when the HVAC runs.
What it costs in New Braunfels
Contaminated insulation removal in New Braunfels typically costs $2.40-$4.20 per square foot of attic floor, or $2,800-$5,200 for standard production-home attics, with HEPA containment and disposal included.
How we do it
We establish negative air pressure with HEPA filtration, remove contaminated material in sealed bags, apply antimicrobial treatment to exposed framing, and document the cleaned cavity with photos before new insulation is specified.
Insulation Replacement
Signs you need it
Your insulation has been removed for electrical or structural work and never properly replaced, or it has settled below the manufacturer’s labeled thickness.
What it costs in New Braunfels
Insulation replacement in New Braunfels typically runs $1.80-$3.60 per square foot for blown-in fiberglass to R-49, or $2,200-$4,800 for standard attics, with air sealing prerequisite work priced separately.
How we do it
We air-seal the attic floor first, then install new blown-in fiberglass from Johns Manville or Knauf to the specified R-value with even depth and proper baffling at eaves, documenting depth measurements with photos.
What Insulation Removal & Replacement Costs in New Braunfels
| Item | Typical range in New Braunfels |
|---|---|
| Contaminated insulation removal (attic) | $2,800 - $5,200 |
| Standard insulation replacement (blown-in to R-49) | $2,200 - $4,800 |
| Removal + replacement package | $4,500 - $8,500 |
Can you remove insulation with asbestos?
We do not handle asbestos-containing materials; if your home was built before 1990 or contains vermiculite insulation, we require third-party asbestos testing and abatement before our crew enters the space.
How do I know if my insulation needs removal or just topping off?
We assess density, moisture content, and contamination during our initial inspection; if the existing material is dry, uncompressed, and clean, we typically recommend air sealing and supplemental insulation rather than full removal.
Attic Air Sealing in New Braunfels
Attic air sealing in New Braunfels is the foundational step we never skip, because the 2010s-2020s production homes that dominate this market were built with visible gaps at top plates, wire penetrations, and duct chases that allow conditioned air to escape continuously. A blower-door test on a typical five-year-old home in the SH-46 corridor often reads 3,500-4,500 CFM50 before sealing, indicating that the equivalent of a small window is open to the attic year-round. We seal first, then insulate, in that order, and we publish the before-and-after blower-door numbers so you can see the air-leakage reduction you paid for. Attic Air Sealing explains our full protocol.
In New Braunfels, the combination of hard summer cooling loads and the freeze-risk exposure revealed by Winter Storm Uri makes air sealing particularly consequential: every cubic foot of conditioned air that escapes in summer must be replaced and re-cooled, and every air leak is a potential cold-air intrusion point during a hard freeze.
Top Plate & Penetration Sealing
Signs you need it
You feel drafts from ceiling fixtures, your attic insulation has dark staining at the edges of walls, or your blower-door test shows excessive leakage despite adequate insulation depth.
What it costs in New Braunfels
Top plate and penetration sealing in New Braunfels typically costs $1,200-$2,400 for production homes under 2,500 square feet, with larger or more complex attic layouts reaching $2,800-$4,200.
How we do it
We access top plates at eaves and interior wall intersections, seal all wire and pipe penetrations with fire-rated caulk and expanding foam, and install rigid blocking at larger openings, with blower-door verification after each zone.
Can Light & Duct Boot Sealing
Signs you need it
Your can lights are hot to touch in summer, you see dust streaks around ceiling registers, or rooms farthest from the HVAC unit are consistently warmer or cooler than the thermostat setting.
What it costs in New Braunfels
Can light and duct boot sealing in New Braunfels typically runs $800-$1,800 depending on fixture count and duct configuration, with IC-rated airtight enclosures installed where standard cans cannot be sealed.
How we do it
We install pre-formed airtight covers or fire-rated boxes over non-IC can lights, seal duct boots to drywall with mastic and mesh, and pressure-test the duct system to verify no leakage remains at the attic interface.
What Attic Air Sealing Costs in New Braunfels
| Item | Typical range in New Braunfels |
|---|---|
| Top plate and penetration sealing | $1,200 - $2,400 |
| Can light and duct boot sealing | $800 - $1,800 |
| Comprehensive attic air sealing (full package) | $2,200 - $4,800 |
Do I need air sealing if my home is only five years old?
Yes, production builders in New Braunfels prioritize speed over envelope tightness, and we’ve documented significant leakage in homes less than three years old; age alone is not a reliable indicator of air-sealing quality.
How much does air sealing lower my energy bills?
Most New Braunfels homeowners see 10-25% reduction in cooling-season energy use after comprehensive attic air sealing, with the exact percentage depending on pre-existing leakage, HVAC efficiency, and thermostat habits.
Wall Insulation in New Braunfels
Wall insulation in New Braunfels addresses a gap that the 2021 freeze made visible: the 2×4 and 2×6 exterior walls in production homes built along I-35 and FM-306 were typically insulated with fiberglass batts that leave voids at corners, headers, and behind electrical boxes, providing far less effective R-value than the labeled rating suggests. When temperatures dropped below 10°F for extended periods, these voids allowed rapid heat loss that froze pipes in exterior walls and mechanical chases. Wall Insulation covers our methods for both retrofit and new construction.
Retrofit wall insulation in existing New Braunfels homes requires careful assessment of the wall cavity condition, vapor drive direction, and existing moisture load before any material is specified.
Injection Foam Wall Insulation
Signs you need it
Your exterior walls feel hot to touch in summer, you have rooms with south or west exposure that never cool evenly, or your energy bills spike despite adequate attic insulation.
What it costs in New Braunfels
Injection foam wall insulation in New Braunfels typically costs $3.50-$6.50 per square foot of wall area, or $4,200-$8,500 for a complete production-home exterior envelope.
How we do it
We drill 5/8-inch holes at stud-bay intervals, inject slow-rise foam that fills around existing wiring and plumbing without displacement, then plug and texture-match the holes, with thermal imaging verification of complete cavity fill.
Drill & Fill Wall Insulation
Signs you need it
Your walls have no insulation or degraded batts that have fallen, and you want dense-pack cellulose or fiberglass without full drywall removal.
What it costs in New Braunfels
Drill-and-fill dense-pack wall insulation in New Braunfels typically runs $2.80-$5.20 per square foot, or $3,500-$7,200 for complete exterior walls, with Knauf or GreenFiber cellulose.
How we do it
We remove a row of siding or drill through exterior sheathing at each stud bay, dense-pack cellulose to 3.5 pounds per cubic foot for no-settle performance, then seal penetrations with weather-resistant flashing and replace siding.
What Wall Insulation Costs in New Braunfels
| Item | Typical range in New Braunfels |
|---|---|
| Drill-and-fill dense pack (cellulose) | $3,500 - $7,200 |
| Injection foam (complete exterior) | $4,200 - $8,500 |
| Interior wall soundproofing | $2,200 - $4,800 |
Will injection foam damage my walls?
Our slow-rise formulations are specifically selected to avoid pressure damage to drywall; we monitor expansion in real time and have completed thousands of injections without structural or cosmetic damage.
Can you insulate walls without removing drywall?
Yes, both injection foam and dense-pack cellulose are designed for retrofit application through small exterior or interior penetrations, with texture and paint matching performed after installation.
Attic Cleaning & Rodent Proofing in New Braunfels
Attic cleaning and rodent proofing in New Braunfels is often the first step before any insulation work can proceed, because the same construction gaps that leak conditioned air also provide entry points for roof rats, squirrels, and raccoons. In the master-planned communities with mature landscaping and greenbelt corridors, we’ve found active infestations in attics with otherwise good insulation that has been contaminated beyond salvage. Attic Cleaning & Rodent Proofing details our full protocol.
We do not install new insulation over contaminated material, and we do not seal an attic without first identifying and closing every active entry point; doing either would waste the customer’s money and create a recurring problem.
Attic Sanitizing & Decontamination
Signs you need it
Your attic has visible rodent droppings, urine stains on insulation or framing, or a persistent odor that enters the living space through recessed lights or duct leaks.
What it costs in New Braunfels
Attic sanitizing and decontamination in New Braunfels typically costs $1,800-$3,600 for standard production-home attics, with heavy contamination or large attic volumes reaching $4,200-$6,500.
How we do it
We remove contaminated insulation in HEPA-contained bags, apply enzyme-based decontaminant to all framing surfaces, fog with antimicrobial where mold is present, and deliver before-and-after photos with a written clearance statement.
Rodent Proofing & Exclusion
Signs you need it
You hear scratching in the attic at night, find droppings in the insulation, or see gnaw marks on fascia boards or roof vents.
What it costs in New Braunfels
Rodent proofing and exclusion in New Braunfels typically runs $1,400-$2,800 for standard homes, with complex rooflines or multiple entry points requiring $3,200-$5,500.
How we do it
We inspect the roofline, soffits, vents, and utility penetrations with motion-activated cameras if needed, seal all entry points with rodent-resistant materials, install vent guards, and provide a one-year re-entry guarantee with documentation.
What Attic Cleaning & Rodent Proofing Costs in New Braunfels
| Item | Typical range in New Braunfels |
|---|---|
| Attic sanitizing and decontamination | $1,800 - $3,600 |
| Rodent proofing and exclusion | $1,400 - $2,800 |
| Complete cleanout, decon, and exclusion | $3,500 - $7,200 |
Do you handle live animal removal?
We coordinate with licensed wildlife trappers for live animal removal before our crew enters; we do not trap animals ourselves, but we will schedule our work immediately after clearance to minimize delay.
How long does attic decontamination take?
Most New Braunfels attic decontaminations take one to two days, with day one for removal and surface treatment and day two for drying, final inspection, and documentation; heavy contamination may extend to three days.
Home Energy Audit in New Braunfels
A home energy audit in New Braunfels is the diagnostic starting point for every major insulation decision, because the production-built housing stock presents a narrow but specific set of failure modes that are invisible without testing. We use blower-door testing, thermal imaging, and duct leakage measurement to identify where conditioned air is escaping, where insulation is missing or degraded, and which upgrades will deliver measurable return. Home Energy Audit explains our full audit protocol.
Every audit in New Braunfels includes a written report with prioritized recommendations, estimated performance impact, and fixed-price quotes for each measure, delivered before any work is discussed.
Blower Door Test
Signs you need it
Your energy bills are higher than comparable homes, you feel drafts despite closed windows, or you’re considering insulation upgrades and want to know where air leakage ranks against insulation deficiency.
What it costs in New Braunfels
A standalone blower-door test in New Braunfels typically costs $350-$550, or is included at no additional charge when bundled with a full home energy audit.
How we do it
We install a calibrated fan in an exterior door, depressurize the house to 50 Pascals, measure the airflow in CFM50, then use smoke pencils and thermal imaging to locate the largest leakage paths for targeted sealing.
Thermal Imaging Inspection
Signs you need it
You have rooms that are consistently warmer or cooler than others, you suspect missing insulation in walls or ceilings, or you want to verify the quality of recent insulation work.
What it costs in New Braunfels
Thermal imaging inspection in New Braunfels typically costs $280-$450 as a standalone service, or is integrated into our full energy audit with written documentation of every anomaly found.
How we do it
We scan the building envelope with a FLIR infrared camera during normal HVAC operation, identifying temperature differentials that indicate missing insulation, air leakage, or moisture intrusion, with photos annotated in the written report.
What Home Energy Audit Costs in New Braunfels
| Item | Typical range in New Braunfels |
|---|---|
| Standalone blower-door test | $350 - $550 |
| Thermal imaging inspection | $280 - $450 |
| Full home energy audit (all diagnostics) | $450 - $850 |
Does the audit fee apply toward work I hire you to do?
Yes, the full audit fee is credited toward any insulation or air-sealing work contracted within 90 days of the audit date, and we apply that credit to the written price before any work starts.
How long does a home energy audit take?
Most New Braunfels audits take three to four hours for a typical production home, with two hours for testing and imaging and one to two hours for the walkthrough and preliminary findings discussion with you on site.
Brands We Service in New Braunfels
We specify materials from Owens Corning, Johns Manville, Knauf, Rockwool, CertainTeed, Icynene, Demilec, and GreenFiber based on the assembly requirements and moisture conditions of each job, with no proprietary product lock-in. Most common batt and blown-in products are stocked locally for next-day availability on approved scopes. our brands
Pricing for Insulation in New Braunfels, TX
| Service | Typical range in New Braunfels |
|---|---|
| Crawl space vapor barrier | $1,800 - $3,200 |
| Crawl space encapsulation | $4,200 - $6,500 |
| Attic radiant barrier | $1,400 - $2,800 |
| Contaminated insulation removal | $2,800 - $5,200 |
| Insulation replacement (blown-in R-49) | $2,200 - $4,800 |
| Attic air sealing (comprehensive) | $2,200 - $4,800 |
| Injection foam wall insulation | $4,200 - $8,500 |
| Attic sanitizing and decontamination | $1,800 - $3,600 |
| Rodent proofing and exclusion | $1,400 - $2,800 |
| Full home energy audit | $450 - $850 |
Prices in New Braunfels trend toward the upper end of these ranges for homes over 3,000 square feet, steep roof pitches that limit attic access, or conditions requiring extensive prep work before insulation can be installed. Every job begins with a written price and written scope before any work starts, under Haven Standard Clause 1, and we provide a Free Second Opinion on any written estimate you bring us.
Neighborhoods We Serve in New Braunfels
Our crews work throughout the New Braunfels metro area, from the historic limestone structures near downtown and Gruene to the master-planned communities that have defined the city’s growth along SH-46 and FM-306. Most New Braunfels appointments are scheduled within 48 hours of initial contact, with emergency response available for freeze-risk and moisture-damage situations.
- Voss Farms and surrounding FM-306 corridor
- Meyer Ranch and SH-46 east subdivisions
- Gruene Historic District and downtown-adjacent areas
- Veramendi and I-35 north corridor
- Copper Ridge and Hill Country fringe properties
Service Area - Cities Near New Braunfels
We serve the full I-35 corridor between San Antonio and Austin, with dedicated crews and scheduling for Seguin, TX, Cibolo, TX, Schertz, TX, and Canyon Lake, TX. Dispatch and scheduling are coordinated from our San Antonio office, with local crews deployed to each market for assessment and installation work.
Serving New Braunfels, TX - Our Local Coverage Area
We’re based in the New Braunfels area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs About Insulation in New Braunfels
Most attic insulation and air-sealing work in New Braunfels does not require a permit, but crawl space encapsulation and wall insulation that involves structural modification may; we handle permit research and application as part of our written scope when required, with no additional fee.
We typically schedule assessments within 24-48 hours for standard inquiries, and our live answering service at (737) 227-6219 can dispatch emergency crews for freeze-risk, active moisture intrusion, or post-storm damage within hours.
Most New Braunfels HOAs regulate exterior appearance rather than attic or crawl space work, but we review your HOA documents before specifying any exterior-access work such as wall injection or roof-deck radiant barrier, and we document compliance in your written scope.
What happens when you call
- 1A real person answersNo phone trees - talk to a local insulation pro.
- 2You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
- 3A background-checked tech heads outLicensed & insured, typically same-day.
- 4You approve before work beginsNothing starts until you say go.
What New Braunfels Customers Say
"They photographed rodent damage in the old insulation that we had no idea about, and priced the exclusion work separately so we could decide."
- Harriet N."Two other companies quoted to blow more insulation on top of what was there. These were the only ones who said the existing material had to come out first, and explained why."
- Clifford E."Crawl space encapsulation done properly. Photographs of the vapour barrier at every seam, and the damp smell in the hallway is gone."
- Ainsley P.