Owens Corning Blown-In Insulation Nationwide

Owens Corning Blown-In Insulation in Canyon Lake: What to Know First

We provide independent Owens Corning blown-in insulation service in Canyon Lake, Texas, with most attic retrofits completed in a single day and pricing put in writing before any work begins. A typical blown-in top-up or full attic replacement runs between $1,800 and $4,200 depending on square footage, existing depth, and whether the attic floor needs air sealing first. We’re not affiliated with Owens Corning - we source their materials as an independent service provider - and we publish before-and-after blower-door numbers on every job so you can verify the result yourself. If your attic insulation is compressing, settling below the joist tops, or your upstairs rooms won’t stay cool through a Canyon Lake August, this page is for you. Call (737) 227-6219 for a free estimate with a written price before we start.

Call (737) 227-6219

How Owens Corning Products Fail - and How We Fix Them

• Owens Corning AttiCat PINK Fiberglass Blown-In Insulation settling below R-38 in homes near the lake. The Hill Country humidity cycle - heavy morning dew, rapid afternoon bake - causes fiberglass to slump in attics with inadequate ventilation. We’ve measured original AttiCat installs at 8 inches where 14 were specified, especially in Canyon Lake’s older lakefront builds off FM 2673. We remove the settled material, seal top plates and can-light penetrations, then reinstall to true depth with a marked ruler photo every fifty square feet.
• Owens Corning ProCat LooseFill Cellulose bridging over irregular joist bays in ranch-style homes. ProCat blows well in open attics, but in the chopped-up framing common to 1980s Canyon Lake ranches, it bridges across truss chords and leaves voids underneath. Our crew walks every bay with a probe rod, breaks bridges by hand, and re-blows before the final depth check. No voids, no guesswork.
• Owens Corning EcoTouch Thermal Batt compression from homeowner storage boards. EcoTouch batts lose half their R-value when compressed by plywood walking boards or holiday decoration bins. We see this constantly in Canyon Lake’s seasonal homes where owners store lake gear in the attic. We relocate storage to platform frames above the insulation plane, replace compressed batts with blown-in to fill irregular cavities, and mark the new walking paths so it doesn’t happen again.
• Owens Corning Raft-R-Mate baffles dislodged by wind-driven rain through ridge vents. The lake’s afternoon thunderstorm pattern can drive water past poorly seated ridge vents, soaking cardboard baffles and collapsing nearby blown-in. We replace damaged baffles with rigid plastic equivalents, seal the ridge vent ends with backer rod and caulk, and document the repair in your photo record.
• Owens Corning blown-in installed over unsealed recessed can lights - a code and performance failure. IC-rated or not, can lights leak conditioned air. Owens Corning’s own installation guidelines specify sealing before insulating, but we’ve found plenty of Canyon Lake attics where the insulation went in first. We pull back the material, install fire-rated covers sealed with mastic, then replace the insulation. The blower-door test proves the fix.

Our Owens Corning Blown-In Insulation Process

1. 1
   Call and schedule. A live person answers 24/7. We book a diagnostic visit, and you’ll get a text when your technician is en route.
2. 2
   Blower-door test and attic inspection. We pressurize the house and measure CFM50 - how much air your envelope is losing. Then we probe the attic: depth, coverage, moisture staining, and whether the attic floor is sealed. You get a printed pre-work number.
3. 3
   Written price and scope. Under Haven Standard Clause 1: flat price, written scope, written warranty before anyone lifts a tool. No surprises.
4. 4
   Air sealing first, then insulation. Top plates, wire penetrations, chimney chases, can lights - sealed with foam, mastic, or fire-rated materials as appropriate. Seal the leaks first. Then insulate. The report tells you whether it worked.
5. 5
   Blown-in installation to specified depth. Owens Corning, Johns Manville, Knauf, or another specified material - we don’t lock you into one brand. Depth is checked with a marked ruler; photos are taken every fifty square feet.
6. 6
   Post-work blower-door test and documentation. We run the test again, print the before-and-after comparison, and add it to your Documented Photo Record. The 365-Day Done Right Promise begins when you sign off.

Before

After

What Owens Corning Blown-In Insulation Costs in Canyon Lake

Most Owens Corning blown-in attic jobs in Canyon Lake run between $1,800 and $4,200. Here’s how the numbers break:

What moves the price: attic square footage, whether old material must be removed, accessibility (scuttle vs. pull-down stairs vs. cut new access), and the extent of air sealing required. Homes near the Cranes Mill Road corridor with original 1970s construction often need more sealing than newer builds. We also provide a Free Second Opinion on any written estimate - bring us a competing quote and we’ll read it with you. Call (737) 227-6219 for your exact number; estimates are free and the price is written before any work starts.

Why Canyon Lake Homeowners Call Topside Attic Insulation Canyon Lake for Owens Corning Work

We’ve sealed and insulated over 9,000 homes since 2016, every one with a written price before work started and a documented record when the crew left. Wes Okafor, our owner and lead technician, learned the building-science side of this trade at Olive-Harvey College’s construction technology program before spending years figuring out why houses in hot-humid climates fail differently than the ones he worked on up north. That background shows up in how we diagnose - we don’t guess, we measure. Our crew knows Owens Corning’s product lines, but we also stock Reflectix and materials from Johns Manville, Knauf, Rockwool, and others, so you’re never locked into a single brand if your job calls for something different. Calls are answered by a live person 24/7, technicians are background-checked and uniformed, and every job ends with a Documented Photo Record and, where applicable, printed blower-door numbers. The 365-Day Done Right Promise covers all completed work - if it’s not done right, we make it right.

FAQs